不銹鋼旋轉供料器
Stainless steel rotary feeder
旋轉供料器也叫卸料器、鎖氣閥、旋轉閥，分普通型、耐壓型、耐高溫型三大類。
Rotary feeders, also known as unloaders, air lock valves and rotary valves, are divided into three categories: common type, pressure resistant type and high temperature resistant type.
無載荷試運轉：
No load test run:
1、確認各配置是否全部連接完畢。
1. Confirm whether all configurations are connected.
2、齒輪傳動馬達是否按廠家使用說明書將潤滑油位補充到標準水平。
2. Whether the lubricating oil level of gear drive motor is supplemented to the standard level according to the manufacturer's instructions.
3、鏈條、鏈罩是否已安裝。
3. Whether the chain and chain cover have been installed.
4、旋轉方向是否正確。 確認以上各項不存在問題后，送電進行十五分鐘的空載運轉。運轉中檢查密封壓蓋處是否漏氣，溫度是否升高，軸承溫度是否升高，有無振動或雜音。一切運轉正常，無載荷試驗結束。
4. Whether the rotation direction is correct. After confirming that the above items are free of problems, power on for 15 minutes of no-load operation. During operation, check whether there is air leakage at the sealing gland, whether the temperature rises, whether the bearing temperature rises, and whether there is vibration or noise. All operations are normal, and the no-load test is completed.
故障排除：
Troubleshooting:
1、雜音
1. Murmur
1.轉子與側板之間滯留粉體物:從側面絲堵部位進體清洗。
1. residual powder between rotor and side plate: conduct gas cleaning from the side plug.
2.機殼與轉子接 擴大間隙，使之達到恰當?shù)拈g隙。
2. the clearance between the casing and the rotor shall be enlarged to make it reach the appropriate clearance.
3.機殼內表面有粉體物附著，粉體物溶化，則側板與轉子間隙消失 縮小轉子端面面積。
3. there is powder attached to the inner surface of the casing. If the powder dissolves, the gap between the side plate and the rotor disappears and the rotor end face area is reduced.
2、振動
2. Vibration
1.鏈條過緊 適當松一下鏈條。
1. if the chain is too tight, loosen the chain properly.
2.有顆粒卡入 安裝緩沖板。
2. there are particles stuck in the mounting buffer plate.
3、排量不足
3. Insufficient displacement
1.由于泄漏氣體的作用，粉粒體下落受到阻礙：采取抽氣措施。
1. due to the effect of leaked gas, the falling of powder particles is hindered: take air extraction measures.
2.粉粒體的容重不同于設計值：提高轉速，使之達到恰當轉速。
2. the unit weight of the powder is different from the design value: increase the speed to make it reach the appropriate speed.
3.卡料 在供料器的正上方或正下方使用軟管，擴大間隙使之成恰當間隙。
3. for clamping, use a hose directly above or below the feeder to expand the gap to make it an appropriate gap.
日常維護：
Routine maintenance:
1、經常檢查旋轉供料器運轉中有無雜音或振動。
1. Frequently check whether there is noise or vibration during the operation of the rotary feeder.
2、密封壓蓋有無氣體泄漏現象。
2. Whether the sealing gland has gas leakage.
3、各部溫升是否正常。
3. Whether the temperature rise of each part is normal.
4、鏈條的松緊程度。
4. The tightness of the chain.
5、各注油部位定時注油。
5. Fill oil regularly at each oil filling position.
The above is Guangdong rotary feeder http://www.25dns.cn/ Thank you for checking the information of our company in your busy schedule. If you want to know more, you are welcome to call us for consultation!
TEL:400-9901-557
TEL:18678880998
公司地址：山東省濟南市章丘區相公街道大康村村南
濟南道源豐達機械制造有限公司
備案號：魯ICP備2022009540號-1 魯公網安備37018102000745號
