How to install common pneumatic conveying equipment?

1、一般情況下，料封泵裝在料倉庫底比較合適，落料順暢。如果放不在庫底，置于旁邊亦可。但落料管斜角≥45°。如果裝在電除塵落灰斗下部，可以一斗一泵，亦可兩斗兩斜管一泵;特殊情況亦可四斗四斜管插入一臺料封泵中，但所有落灰斜管的斜度均應≥45°。

1. Generally, the material seal pump is installed at the bottom of the material warehouse, and the blanking is smooth. If it is not placed at the bottom of the warehouse, it can also be placed next to it. However, the inclined angle of blanking pipe is ≥ 45 °. If it is installed at the lower part of the electrostatic precipitator ash hopper, it can be one bucket and one pump, or two buckets, two inclined pipes and one pump; Under special circumstances, four buckets and four inclined pipes can also be inserted into a material sealing pump, but the inclination of all ash falling inclined pipes shall be ≥ 45 °.

2、料封泵一般置于堅硬的水平地面上即可，無需打基礎安裝地腳螺栓，當風管,出料管連接好以后，即可投運。但要求進風管與泵管連接時應安裝一個撓性節頭。

2. Generally, the material seal pump can be placed on a hard horizontal ground without foundation and anchor bolts. It can be put into operation after the air duct and discharge pipe are connected. However, a flexible joint shall be installed when the air inlet pipe is required to be connected with the pump pipe.

3、料封泵的總高(包括料封泵灰斗)一般為3.5-4.5m，根據現場實際情況亦可適當變動。

3. The total height of the material seal pump (including the ash hopper of the material seal pump) is generally 3.5-4.5m, which can be changed appropriately according to the actual situation on site.

4、料封泵放置出口方向，可根據現場情況而定，一般超向灰?guī)焖谖恢玫姆较驗橐?，或根?jù)管路的走向而定。

4. The outlet direction of the material seal pump can be determined according to the site conditions. Generally, it is appropriate to exceed the direction of the ash silo, or according to the direction of the pipeline.

5、本裝置要求庫頂收塵器的氣體散放量應大于料封泵送料帶風總量。勿使庫內出現正壓情況，以免影響輸灰系統工作。

5. The device requires that the gas emission of the dust collector on the top of the warehouse should be greater than the total amount of air carried by the material seal pump. Do not make positive pressure in the warehouse, so as not to affect the operation of ash conveying system.

6、要求氣源、料封泵、輸灰管全系統密封良好，漏風率小于 0.2%。

6. The air source, material seal pump and ash conveying pipe shall be well sealed, and the air leakage rate shall be less than 0.2%.

氣動式真空上料機即是利用壓縮空氣通過真空發生器產生高真空實現對物料的輸送，不需要機械式真空泵，具有結構簡單、體積小、免維修、噪音低、控制方便、物料靜電和符合GMP要求等優點。真空發生器產生的高真空，使被輸送的物料杜絕了分層現象，保證了混合物料成分的均一性，是壓片機、膠囊填充機、干法制粒機、包裝機、粉碎機、振動篩等機械自動上料的設備。 當壓縮空氣供給真空發生器時，真空發生器就產生負壓形成真空氣流，物料被吸入吸料咀，形成物氣流，經過吸料管到達上料機的料倉內。過濾器把物料與空氣徹底分離，當物料裝滿料倉時，控制器會自動切斷氣源，真空發生器停止工作，同時料倉門自動開啟，物料落到設備的料斗中。與此同時，壓縮空氣通過脈沖反吹閥自動清洗過濾器。等到時間到或料位傳感器發出上料信號時，自動啟動上料機。

Pneumatic vacuum feeder uses compressed air to generate high vacuum through vacuum generator to realize the transportation of materials. It does not need mechanical vacuum pump. It has the advantages of simple structure, small volume, maintenance free, low noise, convenient control, eliminating material static electricity and meeting GMP requirements. The high vacuum generated by the vacuum generator eliminates the stratification of the transported materials and ensures the uniformity of the composition of the mixed materials. It is the preferred equipment for automatic feeding of machinery such as tablet press, capsule filling machine, dry granulation machine, packaging machine, crusher, vibrating screen and so on. When the compressed air is supplied to the vacuum generator, the vacuum generator generates negative pressure to form vacuum air flow. The material is sucked into the suction nozzle to form the material air flow, which reaches the silo of the feeder through the suction pipe. The filter completely separates the material from the air. When the material is full of the silo, the controller will automatically cut off the air source, the vacuum generator stops working, the silo door opens automatically, and the material falls into the hopper of the equipment. At the same time, the air is automatically purged through the anti pulse filter. When the time is up or the material level sensor sends the feeding signal, the feeding machine will be started automatically.

氣力輸送系統的三種分類方法

Three classification methods of pneumatic conveying system

A：懸浮流 物料輸送速度高于懸浮速度，物料在管道中成懸浮狀態流動。此輸送方式適合于低壓稀相短距離輸送。

A: The conveying speed of suspended flow material is higher than the suspension speed, and the material flows in a suspended state in the pipeline. This transportation mode is suitable for low-pressure dilute phase short-distance transportation.

B：集團流 物料輸送速度約等于懸浮速度，物料在管道中成集團狀態移動。此輸送方式適合于中壓較長距離輸送。

B: The conveying speed of group flow material is about equal to the suspension speed, and the material moves in a group state in the pipeline. This conveying mode is suitable for medium pressure long-distance conveying.

C：栓流 物料輸送速度低于懸浮速度，物料在管道中被脈沖氣閥（氣刀）氣壓力切割成栓狀，依靠料栓前后的空氣靜壓差作為推動力前進。此輸送方式適合于高壓密相長距離低速輸送。

C: The conveying speed of slug flow material is lower than the suspension speed. The material is cut into a slug shape by the pneumatic force of the pulse air valve (air knife) in the pipeline, and moves forward relying on the air static pressure difference before and after the slug as the driving force. This conveying mode is suitable for high-pressure dense phase long-distance low-speed conveying.

以上就是為大家介紹的有關江蘇氣力輸送設備的詳細介紹,希望對您有所幫助.如果您有什么疑問的話,歡迎聯系我們.我們將以的態度,為您提供服務http://www.25dns.cn/

The above is the detailed introduction of Jiangsu pneumatic conveying equipment. I hope it will be helpful to you If you have any questions, please contact us We will provide you with professional service http://www.25dns.cn/