In daily use, the rotary feeder should pay more attention to the dust being blocked when it strikes in the ash hopper or falls into rigid materials, so as to avoid damaging the operating equipment. The abrasive dust impeller is quickly worn, and the impeller should be timely repaired. Feeder is a widely used product. Most of the problems will occur in the actual use process. I have summarized several common problems that will occur in the work process.

供料器適用于連續正反運轉，在運行過程中假如發生沿軸向漏風或是漏灰現象，可禁錮壓料蓋的螺絲或是重新更換石棉盤根后再壓緊料蓋即可。供料器在出廠前需要注足潤滑油與潤滑脂，在使用6個月后，傳動及軸承部位應增補或是更換油脂，假如安裝環境的溫度較高或是灰塵過多，都應縮短換油時間。

The feeder is suitable for continuous positive and negative operation. In case of axial air leakage or ash leakage during operation, the screw of the pressing cover can be fastened or the asbestos packing can be replaced and then the material cover can be pressed tightly. The feeder shall be fully filled with lubricating oil and grease before delivery. After 6 months of use, the transmission and bearing parts shall be supplemented or replaced with grease. If the temperature of the installation environment is high or there is too much dust, the oil change time shall be shortened.

旋轉供料器是除塵器密封卸料的專用裝置，它能連續不斷的排料及把物料輸送到指定裝置內，對多種物料均可應用。耐溫型供料器所輸送物料的溫度可達280℃，兩端軸承與葉輪有一定隔離，能防止超細粉料與軸承接觸。耐高溫型供料器輸送物料的溫度高達500℃，采用鏈輪連接，減速機和卸料器殼體有一定的間隔。

The rotary feeder is a special device for sealing and unloading of the dust remover. It can continuously discharge and transport materials to the designated device, and can be used for a variety of materials. The temperature of the materials conveyed by the temperature resistant feeder can reach 280 ℃. The bearings at both ends are isolated from the impeller to prevent the contact between the ultra-fine powder and the bearing. The high temperature resistant feeder conveys materials at a temperature of up to 500 ℃, which is connected by chain wheels. There is a certain distance between the reducer and the discharger shell.

供料器的特點：

Features of feeder:

1、配用擺線輪減速機，結構緊湊，不亂可靠。

1. Equipped with cycloidal gear reducer, the structure is compact and reliable.

2、采用彈性葉輪、增強柔性密封，葉輪卡住現象。

2. Elastic impeller and enhanced flexible seal are adopted to eliminate the seizure of impeller.

3、軸承座移位閥體外側，隔斷塵粒直接來源，延長軸承使用壽命，利便維修。

3. The bearing seat is displaced outside the valve body to isolate the direct source of dust particles, prolong the service life of the bearing and facilitate maintenance.

以上就是為大家介紹的有關廣東旋轉供料器的詳細的介紹,希望對您有所幫助.如果您有什么疑問的話,歡迎聯系我們.我們將以的態度,為您提供服務http://www.25dns.cn/

The above is a detailed introduction to Guangdong rotary feeder, and we hope it will be helpful to you. If you have any questions, please contact us. We will provide you with professional services http://www.25dns.cn/